HOW TO PROGRAM COMPATIBLE NICE REMOTE CONTROLS

How to program the Nice remote control?

For more information, visit our dedicated article on How to Program a Nice Remote Control .

Programming a Nice remote control is simple and requires just a few steps. There are two main methods: using a pre-programmed remote control or directly from the system's control unit.

1. Method with pre-programmed remote control:

   • Get closer to the automation system (1-2 meters).

   • Press the desired button on the new remote control for 5-6 seconds.

   • Use the already configured remote and press the same button 3 times, with 1-second pauses.

   • Press the button on the new remote again for 1 second and wait 10 seconds.

2. Method from the control unit:

   • Open the control unit box and press the programming button.

   • Press the desired button on the remote control until the LED on the receiver flashes or goes out.

For more details, you can consult the manual here or purchase the remote control on Amazon .

How to program the Nice remote control from the control unit?

For complete details, read the in-depth article on Programming the Nice Remote Control from the Control Unit .

Programming a Nice remote control from the control unit requires access to the automation system's receiver.

Procedure:

1. Open the control unit box, identifiable by the antenna cable.

2. Press the programming button on the receiver until the LED lights up.

3. Press the button on the remote control you want to configure until the LED on the receiver flashes or turns off.

4. Press the button on the remote control again to confirm the programming.

This method is useful when you don't have a pre-programmed remote. For more resources, see the PDF manual here .

How to program the Nice Flor-S remote control?

Find the complete guide on How to Program a Nice Flor-S Remote Control .

The Nice Flor-S remote control follows a similar procedure to other models.

Procedure:

1. Approach the automation system.

2. Press the button on the remote control that has already been programmed for 3 seconds.

3. On the new remote, press the button you want to configure for 5 seconds.

4. Wait for confirmation from the LED on the receiver or remote control.

If you need a Nice Flor-S remote control, buy it on Amazon .

How to open Nice remote control?

Check out our detailed article on How to Open a Nice Remote Control .

To replace the battery or check for any faults, you need to open the Nice remote control. Follow these steps:

1. Use a small flathead screwdriver to pry open the side slot.

2. Remove the cover carefully to avoid damaging the internal circuitry.

3. Replace the battery with a new one of the same type (usually CR2032).

4. Close the remote control by pressing both sides until you hear a click.

For a detailed manual, visit this page .

How to duplicate a Nice remote control?

Find out more in our article on How to Duplicate a Nice Remote Control .

Duplicating a Nice remote control is useful for having a spare device.

1. Position yourself near the automation system.

2. Press and hold the button on the original remote control.

3. Press the button on the new remote control at the same time for 5 seconds.

4. Test the operation of the new remote control.

How to duplicate the Nice Flor-S remote control?

Read the full article on How to Duplicate a Nice Flor-S Remote Control .

The procedure for duplicating a Nice Flor-S remote is similar to that for other models. Make sure both remotes are close together during the procedure.

Steps:

1. Press the button on the original remote control until the LED flashes.

2. Press and hold the corresponding button on the new remote.

3. Wait for LED confirmation.

How to program a Nice remote control for awnings?

For a detailed guide, visit Programming the Nice Remote Control for Awnings .

Configuring the Nice awning remote control requires access to the system's motor or receiver.

1. Press the programming button on the awning motor.

2. On the remote control, press the desired button until the system responds (e.g. moving the curtains).

3. Test the remote to make sure it works properly.

If you need a suitable remote control, check out the products available on Amazon .